Announcement

Collapse
No announcement yet.

BOBinGA PS95-8 speakers

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • kenrhodes
    started a topic BOBinGA PS95-8 speakers

    BOBinGA PS95-8 speakers

    I built BOBinGA's ps95 full range design. They are small but deliver the goods. There is something about a good full range design that is amazing and this design delivers that magic.
    The cabinet is 4 1/2 wide 10 tall and 7 deep 1/2 thick tuned to 81hz. Small enough for almost any application. Currently using them in my living room with subwoofers and they get plenty loud for my needs.
    really glad I built this design. It only took 3 evenings from start to finish. I sealed the outside with shellac and then sprayed them with a rattle can. More time on the finish and these could have looked a lot nicer. Being as small as they are they still pass the WAF test.

  • Kootskid
    replied
    Hi, I do not mean to hijack this thread. I am trying to contact BOBinGA and I am not allowed to PM Bob for some reason. Bob, I replied to your thread about the PEDS, and would like your comments. Sorry for the intrusion, I have a message into the Web Master inquiring about my PM privileges.

    Myles

    Leave a comment:


  • joeybutts
    replied
    http://techtalk.parts-express.com/fo...gns-for-ps95-8

    http://techtalk.parts-express.com/fo...-speaker-build

    Leave a comment:


  • joeybutts
    replied
    I do....let me find it....

    Leave a comment:


  • kenrhodes
    replied
    Do you have a design written up for the MLTL? If love to see it.

    Leave a comment:


  • joeybutts
    replied
    I haven’t heard this design but have put the PS95 in an mltl and I feel it is quite impressive.... throw bob’s design in it and let us know what you think

    Leave a comment:


  • Jake
    replied
    BobinGA, thank you for the response, and conformation on my suspicions of the filter. For the record I didn't expect nd90 bass, 80hz is fine. I was just hoping it to be more pronounced.

    Leave a comment:


  • kenrhodes
    replied
    Sorry, I have only used mine with sub woofers so I can't comment on their extension. I would not expect much as this driver has little surface area/x-max to make bass. Good news is that the internet is full of 2.1 amplifiers and sub woofers.
    I would be happy to make some recommendations if you let me know the budget and space options.

    Leave a comment:


  • BOBinGA
    replied
    Yes, the filter will improve the perceived bass response quite a bit. Without the filter, the highs just keep getting louder and louder as you go up in frequency. But also keep in mind that 80hz is about their limit. They are only a 3" driver after all.

    Leave a comment:


  • Jake
    replied
    Can anybody comment on the bass response of these? I threw them in an 80hz test box with no filter and was less than impressed based on all the reviews. I'm assuming the filter will smooth/balance out the sound possibly making them sound fuller? My intended use is 2 channel stereo listening.

    Leave a comment:


  • Jake
    replied
    I just ordered the parts for this project today, but mine will likely be a standard round port. I don't have much time these days with 2 little ones. Looking forward to hearing them.

    Leave a comment:


  • BOBinGA
    replied
    I don't think I did a full write up on these, but everything you need should be in this thread. I originally posted this as comment 22 in this thread:
    techtalk.parts-express.com/forum/tech-talk-forum/1294373-designs-for-ps95-8/page2

    The only thing I would add is that this is designed flat on axis. Ken commented "
    They do loose the top end off axis but not as bad as I expected." This is normal for any full range driver. If you want them a little brighter off axis, you need to make them a tad bright on axis. If you want to experiment with this, changing the first .45 mH inductor to something less might help. Something like .3 or .4 will do it. But I listened to these for quite a while designing them and finally settled on .45 as the most natural sounding within 3 to 10 feet away. In a bigger space, you will not get the high frequency reflections off your walls, so reducing the inductor might help in that case. Season to taste, but keep the L2-C2-R2 notch filter as is so that it hits the peak at 2000 hz and flattens it out.

    C1 is there as protection for low frequency explosions and such. This speaker has its power limits and C1 keeps it from exceeding Xmax with material below about 50 hz. It does not affect the sound in the normal 80 hz and above band that this is designed for. I marked it as optional because most receivers have a high pass filter when set up with a sub, so in that case it could be left out and you would likely be OK, but better safe than sorry.

    -Bob

    Leave a comment:


  • AWholeCorndog
    replied
    Have a couple of PS95-8s and this like a good project to use them. Is there a link available with more information, or just what has been posted here. I searched and could not find this specific project. Just curious about C1 being listed as optional, and don't know enough about crossovers to know what it does.

    Leave a comment:


  • BOBinGA
    replied
    Thank you for the kind review. My cat likes them, too.

    Leave a comment:


  • kenrhodes
    replied
    I've been listening to these in my main living room since I built them and now it's time for a casual review.
    This design has all of the strengths of a full range speakers with only a few of the weaknesses. In their current set up they sit on top of 2 10 inch subwoofers that take care of the bottom end with ease. Using my Onkyo receiver I was able to find a desirable crossover point at about 150hz. The combination sounds very full and has not sent me running back to my 2way bookshelf speakers like other thin sounding full range speakers have done. They do loose the top end off axis but not as bad as I expected. Elevating the speakers to ear level did help their sound quality for listening at the sofa. Although my favorite listening position has been on the living room floor with the speakers pointed down at me in a near field trifecta. This seems to turn any floor bounce into chest bounce mitigated by my face mounted audio diffraction device. ;)> They have a good level of detail able to point out some recording flaws but also able to glance over others and let you enjoy the music. The "point source" makes listening to female vocals a joy as the sound stage is solid and defined, no "girl on a trampoline" effect cases by a bad tweeter/mid crossover. They also disappear in the room leaving you ears the ability to imagine the band playing. They also disappear enough to lessen the whining sounds caused by speakers with a lower WAF. These fulfill the need for good audio in a pretty package. Using them in a living room does stretch their abilities a bit but they can get the job done when implemented correctly. I am certain that they would be excellent on a desktop or in a bedroom. I hope that if you try this design you are as happy with them as I am. Thanks for reading my casual review i hope it was entertaining and enlightning. Please feel free to share your thoughts.

    Leave a comment:

Working...
X