-
Older Activity
-
Yesterday, 09:48 AM
Speaking of awesome......
www.youtube.com/watch?v=HiWOxcpxVvs
22 replies | 695 view(s)
-
Yesterday, 08:17 AM
www.google.com/#q=3m+dual+lock&hl=en&source=univ&tbm=shop&tbo=u&sa=X&ei=lgieUfrwJpLeqAGJs4GIBw&sqi=2&ved=0CDsQsxg&bav=on.2,or.r_qf.&bvm=bv.46865395,d....
12 replies | 316 view(s)
-
Yesterday, 08:12 AM
I put mine on the bottom, through the back.
7 replies | 282 view(s)
-
05-22-2013, 03:04 PM
If you mean the video assembling the transmission line cab, there is also a huge hole in the back of the cab that you can use for access. It's a...
7 replies | 282 view(s)
-
05-21-2013, 10:00 PM
Erich H probably could get hold of Kevin Haskins, the diycable website operator.
44 replies | 2616 view(s)
-
05-21-2013, 09:59 PM
I only meant that Selah Audio didn't show a kit available. I remember when you offered the design for a contribution to a charity.
44 replies | 2616 view(s)
-
05-21-2013, 08:02 AM
Good. PE always warns the customer that orders can't be changed after submission. I never tried. Glad you can do that.
13 replies | 572 view(s)
-
05-20-2013, 09:12 AM
I have used it. You do need good square boxes, and yes, it's pretty thick so the edges show. Wolf uses it.
11 replies | 472 view(s)
-
05-19-2013, 11:53 PM
I'd worry more about my ears than my speakers.
41 replies | 850 view(s)
-
05-19-2013, 07:15 PM
That is very pretty. So how did you make that hole?
6 replies | 266 view(s)
-
05-19-2013, 10:29 AM
That thread is a couple of years old. I believe Selah Audio has moved on from that design.
44 replies | 2616 view(s)
-
05-19-2013, 10:11 AM
Good luck on cancelling the order, please report your results.
13 replies | 572 view(s)
-
05-15-2013, 08:57 AM
He's watching you
110 replies | 4198 view(s)
-
05-14-2013, 07:37 PM
If your power goes out, blame George Westinghouse.
...
110 replies | 4198 view(s)
-
05-14-2013, 12:03 PM
Look at:
www.classdaudio.com
10 replies | 376 view(s)
-
05-14-2013, 09:19 AM
I think the OP clarified that these are for stereo music. I guess it's just down to a 3 way with separate amplification for the (sub)woofer. It's all...
46 replies | 1455 view(s)
-
05-14-2013, 07:47 AM
I'd like to see you build that last design. Lots of people discuss an integrated sub design like that, but I can't recall any builds. Here's a design...
46 replies | 1455 view(s)
-
05-13-2013, 11:19 AM
Right now, with all the cheap outdated A/V receivers for sale, it always comes down to this.
16 replies | 547 view(s)
-
05-13-2013, 10:36 AM
youtube?
www.youtube.com/watch?v=PcMhYvXrYBo
21 replies | 571 view(s)
-
05-13-2013, 10:28 AM
I have a PE 2.1 plate amp of similar power. It's fine for a computer sound system, I wouldn't try it for a larger room. Can't comment on your dhgate...
16 replies | 547 view(s)
-
05-13-2013, 10:06 AM
Well, have you seen this design? Just add your own MTM design. One piece. Separate plate amp or not, your choice.
...
46 replies | 1455 view(s)
-
05-12-2013, 06:03 PM
And a quick check on ebay found pro logic receivers going for very low prices.
46 replies | 1455 view(s)
-
05-12-2013, 05:48 PM
Some stereo receivers have a sub out connector but no real bass management. The sub out is a full range signal and depends on the plate am to filter...
46 replies | 1455 view(s)
-
05-12-2013, 01:08 PM
What's funny is I like Paul C's Tarkus project, but not a little slant front monitor. HiVi has a similar design that I also don't like, aesthetically.
32 replies | 1085 view(s)
-
05-12-2013, 01:02 PM
I remember a while back someone built The Copper Project, and complained here that it sounded bad to them. The thread seemed to cause a bit of...
110 replies | 4198 view(s)
-
05-12-2013, 12:20 PM
Here:
www.audioheuristics.org/projects_gallery/Peerless_2_way/Charlies2way.htm
7 replies | 188 view(s)
-
05-12-2013, 11:56 AM
I would call this a simple angled stand, five pieces of wood, one or two angled cuts, depending on your sensibilities. I personally would prefer a...
32 replies | 1085 view(s)
-
05-12-2013, 11:30 AM
Couldn't the tool challenged builder just build a square box of equivalent volume and tilt it back the required 14 degrees with simple angled stands?
32 replies | 1085 view(s)
-
05-12-2013, 11:25 AM
A spiral down cut bit will not splinter veneer and plywood like an up cut, learned that the hard way.
4 replies | 178 view(s)
About djg
- Location:
- wisconsin
- Interests:
- audio, motorcycles
- Occupation:
- aircraft mechanic
Total Posts
- Total Posts
- 2,620
- Posts Per Day
- 1.44
General Information
- Last Activity
- Today 07:52 AM
- Join Date
- 05-31-2008
- Referrals
- 0
1 Friend
Showing Friends 1 to 1 of 1
|
Your #1 Source for Audio, Video & Speaker Building Components
Clearance Center
Deal of the Day
New Products
View Our latest
Sales Flyer
Prices Effective
Through 6/30/13
Order our FREE 336 Page Full Color Catalog
Speaker Component Categories
Home Audio Speakers
Professional Audio & Guitar Speakers
Car Audio Speakers
Speaker Buyouts
Measurement & Design Tools
Subwoofer Plate Amplifiers
Full-Range Plate Amplifiers
Crossover Components
Cabinet Hardware & Speaker
Grill Cloth
Speaker Cabinets
Subwoofer System Kits
Speaker Kits
Speaker Repair Parts
Speaker Wire
|
![$vboptions[bbtitle]](images/techTalkHeader-leftGray2.jpg)
![$vboptions[bbtitle]](images/techTalkHeaderRepeatGray3.jpg)
Find latest posts
View Blog Entries
