Announcement

Collapse
No announcement yet.

UM18-22 Flat Pack Build (step-by-step)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • jtwrace
    replied
    Thanks!

    Leave a comment:


  • ceiol
    replied
    nice write-up. some serious subwoofers!

    Leave a comment:


  • djg
    replied
    Nice documentation, thanks.

    Leave a comment:


  • jtwrace
    replied
    And finally the completed sub with a measurement:

    Click image for larger version

Name:	Complete!2.JPG
Views:	460
Size:	62.0 KB
ID:	1451638


    Click image for larger version

Name:	UM18 scaled.jpg
Views:	584
Size:	59.1 KB
ID:	1451639



    Still looks small compared to my other diy sub:

    Click image for larger version

Name:	sub2.jpg
Views:	448
Size:	51.5 KB
ID:	1451640

    Leave a comment:


  • jtwrace
    replied
    I was confident that it was all correct as I always check each step; however, it's so much easier to check now as a complete assembly...

    Click image for larger version  Name:	Battery Polarity2.JPG Views:	0 Size:	97.9 KB ID:	1451636

    Leave a comment:


  • jtwrace
    replied
    Install the driver!

    Click image for larger version

Name:	bolts installed2.JPG
Views:	668
Size:	117.1 KB
ID:	1451634

    Leave a comment:


  • jtwrace
    replied
    Stuff it!

    Click image for larger version  Name:	Stuffing2.JPG Views:	0 Size:	39.5 KB ID:	1451632

    Leave a comment:


  • jtwrace
    replied
    Next was to solder the Belden 1313A to the Neutrik speakON and install into the cabinet

    Click image for larger version  Name:	Soldered speakON2.JPG Views:	0 Size:	46.2 KB ID:	1451630

    Leave a comment:


  • jtwrace
    replied
    Now you might be wondering what it looks like underneath? Of course, I'll show you a terrible pic!


    See how it squeezed out evenly? Now you might want to touch it and remove the extra. Do not! Why? You run the risk of getting it on the bolt and not even knowing that and then when you go to remove them, you realize what happened.

    Click image for larger version

Name:	IMG_35372.JPG
Views:	668
Size:	36.2 KB
ID:	1451628

    Leave a comment:


  • jtwrace
    replied
    So the little teeth on the Tee Nut are obviously meant to penetrate the substrate - MDF in this case. If you hammer them in, the teeth get bent and mangled and usually cause more harm than good and also put the Tee Nut in crooked which can lead to cross-threaded bolts. That is a nightmare!


    So using those grade 5 bolts and washers you "draw" the Tee Nut up into the substrate. DO NOT tighten too tight, just enough to squeeze the extra PL out and hold it. Remember: The PL is really what is holding the Tee Nut, not those goofy teeth. I personally like to leave the bolts in for 48 hrs to make absolute certain the PL has fully cured.


    Click image for larger version

Name:	image_87350.jpg
Views:	671
Size:	34.5 KB
ID:	1451625

    Leave a comment:


  • jtwrace
    replied
    Now this is very important. If you get the PL on the threads of the Tee Nut, you're screwed!


    So I put 3 dabs around the side of the Tee Nut like below.

    Click image for larger version

Name:	PL on T nut2.JPG
Views:	674
Size:	76.2 KB
ID:	1451623

    Leave a comment:


  • jtwrace
    replied
    I really dislike drivers being held in with wood screws. If you ever need to remove a driver more than once, the hole is usually buggered up as it's not really made for multiple disassembly. So how does one deal with that? Tee Nuts! This is how I use them...


    First you need to purchase some quality tee nuts as these are meant for a permanent installation. I will be using SHCS as my finish bolt to hold the 45 lb 18" driver in.


    So you get the Tee Nuts and some basic grade 5 bolts with washers along with PL Adhesive as seen below. See where this is going?

    Click image for larger version

Name:	T Nut Install2.JPG
Views:	678
Size:	72.5 KB
ID:	1451621

    Leave a comment:


  • jtwrace
    replied
    Next up was waiting a few days for the Duratex to harden (takes up to 7 days) enough to handle the cabinet. Spent lots of time on the water during this time.

    Leave a comment:


  • jtwrace
    replied
    2-3 coats of Duratex provides an excellent finish. I have found that while you put it on heavy, it really takes rolling it in all directions to smooth it out evenly. Then for the final finish, you slowly roll one direction with no pressure with 50% overlap. No zebra stripes and a consistent texture

    Click image for larger version

Name:	finished top2.JPG
Views:	677
Size:	55.4 KB
ID:	1451617

    Click image for larger version

Name:	finished baffle2.JPG
Views:	665
Size:	78.4 KB
ID:	1451618

    Leave a comment:


  • jtwrace
    replied
    I like to finish the inside. If it was ever sold and someone opened it, I like it to look finished. Also, it really cuts down on the possible MDF dust and just makes it so much nicer to me. How crappy is it to open a speaker and see it raw and cheesy inside? Yuck. Doesn't take much more effort to make it look a bit nicer and an advantage of diy since you're not against the Excel Sheet of the bottom line

    Click image for larger version

Name:	IMG_35112.JPG
Views:	680
Size:	43.6 KB
ID:	1451614

    Leave a comment:

Working...
X